Sale: 20% off everything through Dec 1
Wine Country Woodworks

Stabilizing Wood with Cactus Juice: My Best Tips for Pen Blanks and Burl

By Casey Martin · Updated

Video: 10 Best Tips I've Learned For Stabilizing Wood with Cactus Juice
10 Best Tips I've Learned For Stabilizing Wood with Cactus Juice

This is how I stabilize wood with Cactus Juice, the stabilizing resin I've used for years on pen blanks, maple burl, knife scales, grapevine and even sweet gum pods. By the end you'll know how to stabilize wood for pen blanks from start to finish: drying it, pulling vacuum without making a mess of your pump, soaking it long enough, curing it with almost no cleanup, and storing it so it's ready to cast.

Stabilizing means pulling the air out of the wood under vacuum, letting the resin soak into all those empty pockets, and then curing that resin with heat. The process works on pretty much any wood or material. It's not hard, but it's a waiting game, and it doesn't hurt to wait longer on any part of the process.

Video: 10 Best Tips I've Learned For Stabilizing Wood with Cactus Juice
10 Best Tips I've Learned For Stabilizing Wood with Cactus Juice

What you need

  • Cactus Juice stabilizing resin from TurnTex. It comes with a how-to sheet, and those instructions are excellent. Read them.
  • A vacuum chamber and a vacuum pump. I started with a Mason jar and a TurnTex lid that fits jars in a range of sizes. If you buy a chamber that wasn't made for Cactus Juice, get one with a glass lid (more on that below).
  • Weights to keep the wood under the resin. I use scuba diving weights (mine are 2.5 lb and 5 lb, from a local dive shop) and a cast iron floor drain cover.
  • An oven you can trust for curing: a toaster oven, or a smoker if you need more space, plus a separate oven thermometer.
  • A grate and a drip tray for curing, with a foil liner in the tray.
  • Paper towels, a utility knife for bleed-out, and a funnel to put leftover resin back in its jug.
  • Airtight storage for wood before and after stabilizing.

How to stabilize wood, step by step

1. Dry the wood completely.

  • When I say dry, I mean 0% moisture. The maple burl pen blanks in my how-to video were dried at 220°F in an oven for 24 hours.
  • Another way to be sure: weigh the wood, dry it again, weigh it again, and keep going until it stops losing weight.
  • Keep dried wood in an airtight container until it goes in the chamber.
  • Dryness also affects warping. In one batch of maple burl blanks, about 50 or 55 came out perfectly straight. The few that warped slightly were the ones that weren't perfectly dry.

2. Load the chamber and weigh it down.

  • Put the wood in, set your weights on top, and pour in the Cactus Juice.
  • Fill it a few inches above the top of the wood. The wood soaks up a lot of resin; on one batch of pen blanks the level dropped about two inches. You need enough resin left over the wood for the soak.

3. Pull vacuum slowly at first.

  • As soon as the pump starts, the wood throws off a lot of bubbles and they climb toward the top of the chamber. If Cactus Juice gets into your air line and vacuum pump, it's all bad.
  • What I do: as the bubbles get close to the top, I stop pulling from the front and slowly bleed air in at the back valve until the bubbles drop. Then I close the valve partway so the bubbles come back up, but I never fully close it until I'm sure they won't be a problem.
  • This juggling takes a handful of minutes. Once the bubbling settles down to a steady level, let it go to full vacuum.
Video: How To Stabilize Pen Blanks (Or Any Wood)
How To Stabilize Pen Blanks (Or Any Wood)

4. Hold vacuum until the bubbles stop.

  • It's done when no more of the little bubbles are coming up. On my maple burl pen blanks that was about four or five hours, and I let it go a couple of hours more. My sweet gum pods ran about five or six hours.
  • Tiny bubbles that keep coming are moisture, which means the wood could have used more drying. An occasional big bubble is just trapped air.

5. Soak it overnight, or longer.

  • Turn off the pump and let the wood sit in the resin. Soaking is when the resin actually goes into all those empty air pockets.
  • In my opinion soaking is the most important step in the whole process, and the one people skip because they're ready to get it in the oven. If you run the pump for eight hours and only soak for two or three, you could have run the pump for less and gotten about the same result.
  • I almost always soak overnight. If you're dye stabilizing, the time matters even more.

6. Drip dry and wipe off the excess.

  • Pull the pieces out and let them drip back into the chamber. Cactus Juice is reusable, so save every bit you can and funnel the leftover back into the jug.
  • Drip dry as much as possible so you have less mess after curing. On pieces that are hard to clean up with a saw or sander, like grapevine or live edge, I also wipe each piece with a paper towel.
  • Get them into the preheated oven as soon as you can after they come out of the resin.

7. Cure it on a grate, not in foil.

  • I used to wrap pieces in tin foil, even rolling sweet gum pods into individual foil balls. Now I set the wood right on an oven grate with a drip tray underneath. Bleed-out either drips off or cures on a few lines of the grate, and cleanup is much easier.
  • Foil catches all the bleed-out against the wood. I don't really recommend it for pen blanks, and I don't recommend it at all for live edge or burl caps.
  • Line the drip tray with foil, rolled up at the sides like a little boat, and toss it when it gets caked with Cactus Juice.
  • Stand thick blanks up on end, and tilt live edge pieces so any resin left on them runs down and drips off with gravity.

8. Cure it long enough at the right temperature.

  • Cactus Juice cures with heat. In my older videos I cured at 200°F (anywhere from 190°F to 200°F was fine). In my newer pen blank video I set the smoker to 195°F because it runs lower than its own thermostat says, and my separate thermometers read about 180–185°F. From what I've heard, Cactus Juice can cure at 180°F at the minimum.
  • I cook for about 3 to 4 hours minimum. My early videos said a couple of hours, but I've since gone longer. Big pieces of grapevine or large dye-stabilized pieces sometimes get 7 to 8 hours because there's so much volume.
  • It's not done if the wood looks wet anywhere, even if you can't see liquid Cactus Juice. A patchy wet-and-dry look means keep cooking. When the bleed-out is solid, it's cured.
Video: Stabilizing Grapevine with Cactus Juice
Stabilizing Grapevine with Cactus Juice

9. Scrape bleed-out while it's still warm.

  • This is my trick for grapevine, sweet gum pods and anything else that's hard to clean up later. Leave the oven on and take out one piece at a time.
  • Bleed-out on the outside stays soft for a minute or two after it comes out, while the resin inside is already hard. Scrape it off right away with a utility knife.

10. Store it airtight.

  • Stabilized wood has no moisture inside, but humidity in the air can still settle on the surface. I've followed every step perfectly, left wood in a ziplock bag that wasn't sealed, and gotten cloudiness where the resin met the wood when I cast it.
  • Make it airtight however works for you. Zack Higgins wraps his in plastic wrap, puts that in a ziplock bag, and puts the bag in an airtight bin.
  • Before casting, I put stabilized wood in the toaster oven for 10 to 15 minutes (anywhere from 10 to 20 is fine) at around 200°F to drive off any surface moisture.

Common problems and fixes

Cactus Juice bubbled up into the pump

You pulled full vacuum too fast or overfilled the chamber. Bleed air in at the valve as the bubbles climb, and only close it all the way once the bubbling has settled. On chambers with the inlet on the side, you can only fill up to the inlet.

Cloudy resin where the wood meets the casting

That's surface moisture from storage, not a bad stabilization. Store stabilized wood airtight and give it 10 to 15 minutes in the toaster oven at around 200°F before you cast it.

Blanks warped in the oven

In my experience that comes from wood that wasn't perfectly dry going in. Dry until the weight stops dropping. A slight warp on the end of a pen blank usually doesn't matter, since most people cut blanks in half for pens anyway.

Hard bleed-out crusted on the wood

Drip and wipe the pieces before curing, cure on a grate instead of foil, and scrape the bleed-out off while it's still warm.

My acrylic chamber lid cracked

Most acrylic lids on chambers not made for Cactus Juice are too thin. Under vacuum they develop micro cracks all through the lid, and after a couple of uses they're useless. Get a glass lid, ideally with the inlet on top so you can fill the whole chamber. On my 3-gallon glass chamber with the inlet on the side, I lose about a fifth or a sixth of the capacity.

The holes in my wormy wood didn't fill

Stabilizing fills cracks and very small voids, not big holes. If you want large voids completely filled, you'll still need to cast them with resin.

FAQ

How long should I leave wood under vacuum?

Until the small bubbles stop coming up. For me that's usually several hours: about four to five on maple burl pen blanks, five to six on sweet gum pods. Then soak it overnight.

How long does stabilized wood need to soak?

Overnight or longer. Ideally it soaks twice as long as the vacuum ran, or more, and soaking is the step I think matters most.

Should stabilized wood sink?

In theory, perfectly stabilized wood shouldn't float. In my experience some pieces still float even when everything was done right, with good dye penetration and no bubbles left. I don't use floating as the final test.

Can I reuse Cactus Juice?

Yes. Let the pieces drip back into the chamber and funnel the leftover resin back into the jug.

Can I run more than one chamber on one vacuum pump?

Yes. I asked Curtis at TurnTex about it a while back, and I now run three chambers off one pump with a quick connect and multiple outlets. That lets me stabilize grapevine, burl and dye batches at the same time.

Do I need a special oven?

No. A toaster oven works, but use a separate thermometer you trust. When I ran out of room I moved to a 30-inch smoker, which gave me about five to six times the space of a toaster oven. It also goes down to 100°F, so you can use it for drying green wood.

If you'd rather start with blanks that are already done, I sell stabilized maple burl pen blanks and knife scales. For color, see my guide on dye stabilizing wood.

Products in this guide

← All guides