Sale: 20% off everything through Dec 1
Wine Country Woodworks

Dye Stabilized Wood: How to Single, Double and Multi Dye Stabilize (How to Make Stabwood)

By Casey Martin · Updated

Video: How To Dye Stabilize Pen Blanks
How To Dye Stabilize Pen Blanks

Dye stabilized wood is regular stabilizing with color added to the stabilizing resin. Do it once and you get a single color. Do it two or three times in different colors and you get double dye or multi dye stabilized wood, the colorful burl that's also called stabwood. This guide is how I do it, mostly on maple burl pen blanks, but the process is the same for any type and any size of wood, from pen blanks to live edge burl.

By the end you'll be able to get two or three colors into one batch of pen blanks: two colors pulled in from the ends by capillary action, then a third from a full soak under vacuum.

Video: How To Dye Stabilize Pen Blanks
How To Dye Stabilize Pen Blanks

I learned this from Zac Higgins' video on dye stabilizing, and I've added a few tweaks of my own that I think are very beneficial. This guide covers the color part. For the basics of vacuum stabilizing and curing, see my guide to stabilizing wood with Cactus Juice.

What you need

  • Dry wood. I mostly use maple burl and box elder burl. I used to use my own offcuts, but now I buy raw maple burl pen blanks in bulk because it's much easier.
  • Cactus Juice stabilizing resin, dyed in several colors. I keep a cup of each color: red, blue, purple, green, orange, and I've also used teal, pink and black.
  • Cups for the capillary soaks, one per color.
  • Plastic wrap or rubber bands to hold a bundle of pen blanks together.
  • A vacuum chamber for the full soak. If the opening is big enough, you can also put a whole cup inside it.
  • An oven for curing. I use a smoker with racks, and I check its temperature with separate oven thermometers.
  • Sandpaper or a sander for opening up the wood between colors, and a finish to see the color at the end (I've used a spray finish and boiled linseed oil).

Step by step

  1. Plan your colors before anything touches the dye. Each batch is going to get three colors, so think about how they'll look together. Some things I've learned:
    • Green and red look good together, and I think black goes really well with red.
    • Black is very overpowering. I only do a small batch in black, and I follow it with something bright like pink to lighten it up.
    • Don't use a final color that's too close to one you already used. I didn't put my pink-dyed blanks into red for the final soak because pink and red would have looked almost the same.
    • Red and blue are the most versatile final soak colors. For a while those were the only two I used for full soaks: anything that had red in it went into blue, and anything with blue went into red.
    That said, it's all personal preference. You can just start dropping stuff in and it will probably work out. That's the beauty of it.
  2. Bundle the blanks. My maple burl came wrapped in plastic wrap. I peeled the wrap back just enough to leave each bundle together in one piece, because that's the most I could fit in a cup. A rubber band works too.
  3. First color: capillary soak. Stand one end of the bundle in a cup of dyed resin. The wood doesn't need to be submerged. Capillary action pulls the resin up into the wood, so you get color where it's sitting and as far up as it gets pulled.
    • Give it at least 10 to 15 minutes. You can leave it for a day; the longer it sits, the further up it pulls.
    • After about 15 minutes you'll see the color climbing up the blanks. That's purely capillary action, not splashing.
  4. Let them drip dry. This takes five to ten minutes. You don't have to, but it's less messy when you take the wrap off to flip them, and most importantly it keeps the outside resin from dripping into your next color and contaminating it.
  5. Second color: flip and repeat. Take off the wrap, regroup the blanks with rubber bands, flip them over and stand the other end in a second color for another 10 to 15 minutes. Then let them drip dry again.
  6. Cure. I put them in the smoker and cure them overnight. When they come out they'll look colorful on the outside, but there's less color inside than you'd think. That's good: it means there's still plenty of room for the final soak color.
  7. Sand the sides. Before the final color, I sand off some of the sides. There are two reasons:
    • Cured Cactus Juice seals the wood. Sanding breaks into the parts it hasn't reached and opens up the pores so the next color can penetrate a lot easier. You can probably get away without it to a point, but for the best penetration I'd say it's almost necessary.
    • It shows you how far the first colors actually went in. On one grapevine piece I sanded, the red had gone in a little, but not all the way through.
    On irregular pieces like grapevine or live edge burl, hand sand lightly so you keep the shape. On pen blanks, just sand the faces that are already cut.
  8. Final color: full soak under vacuum. Put the blanks in the chamber with the third color and make sure the resin covers them completely. From here it's normal stabilizing, just like any other wood:
    • Pull vacuum until there are no more bubbles.
    • Let them soak for at least twice as long as you pulled vacuum. I usually pull vacuum during the day and let them soak overnight.
    • Check the resin level while they soak. One batch in green soaked up so much that the tops of the blanks were exposed by the next morning. If I'd caught it sooner, I would have topped it up. Those were six inch blanks, so the extra length saved me.
    In my opinion this step has to be done under vacuum for really good penetration.
  9. Cure again. Cure them on a rack rather than wrapping them in foil. The rack catches the drips and it's much easier to let them drip dry that way. You'll still get some little drip lines, so plan to sand or cut those off.
  10. Cut, sand and finish. Before they're cut and finished you really can't tell what you've got. As soon as the finish goes on, the color and the depth of the burl pop out. That's my favorite part.

More colors, bigger pieces

You can repeat this as many times as you want. A larger piece of burl can get a different color on each end, then go into a third color for the full soak. On small pieces it's harder to keep the color on just one part, so you'd have to rig something up so it only sits in a little bit of resin. Another option is little eyedropper vials filled with your own dye to pinpoint colors, but I think the cups are a really good way to get good penetration.

Older method: capillary soaks under vacuum

In my 2019 video I put the capillary cups inside the vacuum chamber and pulled vacuum, so the soaking end gets the air pulled out of it like regular stabilizing, then let them soak at least 24 hours. You'll see a lot of bubbles come out that wouldn't if the cup was just sitting on the bench, and I believe it gives much better penetration on the soaking part. In my newer 2020 pen blank video I did the capillary colors in plain cups for 10 to 15 minutes and saved the vacuum for the final soak, which is simpler and worked well. If your chamber fits the cups and you want deeper end colors, the vacuum method is worth trying. Zac does it with plain cups and gets good results too.

Video: How To Double Dye or Multi Dye Stabilize Wood (How To Make Stabwood)
How To Double Dye or Multi Dye Stabilize Wood (How To Make Stabwood)

Using your dye stabilized wood

You can turn the blanks as they are, or cast them with resin into hybrid blanks and blocks. When I cast dyed burl I hold it down with duct tape or scrap HDPE instead of hot glue, which is messy and can get into the resin. I filled my pressure pot to a little over 50 PSI for about an hour and a half with Alumilite. I often dye stabilize burl and don't cast it for a while, so it's always a surprise to cut the blocks open and see what's inside.

Common problems and fixes

The color didn't go all the way through

This is the most common one. Sand the sides between colors to open the pores and check penetration, and always do the full soak under vacuum. Sanding still isn't a perfect indicator, though. When I turned a multi dye stabilized black ash burl block into a bottle stopper, I was really happy to see the color was still showing once I'd turned into it a decent amount.

Video: Woodturning A Unique Bottle Stopper - Multi Dye Stabilized
Woodturning A Unique Bottle Stopper - Multi Dye Stabilized

Colors look muddy or the same

Plan the colors ahead, keep black to small batches, and don't finish in a color that's close to one already in the wood.

One color is bleeding into the others

Let the blanks drip dry for five to ten minutes before you flip them or move them to another color.

The tops of the blanks came out of the resin

Some wood soaks up a lot. Check the level during the soak and top it up.

Drip lines after curing

Cure on a rack and sand or cut off the sides that have them.

FAQ

How long should the capillary soak be?

At least 10 to 15 minutes. You can leave it for a day. The longer it sits, the further the color climbs.

What's the difference between single, double and multi dye stabilized wood?

Single dye is one color. Double dye is two. Multi dye means more than two colors in the same piece.

Do I need a vacuum chamber for dye stabilizing?

For the full soak, yes. I think it has to be under vacuum for really good penetration. The capillary soaks work in plain cups, but I believe putting the cups under vacuum gives much better penetration.

Why sand between colors?

Cured stabilizing resin seals the wood. Sanding opens the pores so the next color can get in, and it shows you how far the last color went.

Can I dye stabilize larger pieces, not just pen blanks?

Yes. The process is the same for any type and size of wood. I've done live edge burl, buckeye burl, grapevine and black ash burl blocks.

Can I get the exact same blank twice?

Not really. Dyed burl is very hard to replicate, especially multi dye, which is why I sell these as limited edition batches.

If you'd rather start with burl that's already stabilized, my stabilized maple burl pen blanks are solid grade 5A maple burl, stabilized and ready to turn.

Products in this guide

← All guides