Sale: 20% off everything through Dec 1
Wine Country Woodworks

Pinecone and Sweet Gum Pod Pen Blanks: Stabilizing and Casting Natural Inclusions

By Casey Martin · Updated

Video: Mini Pinecones & Alumilite Pen Blanks?!
Mini Pinecones & Alumilite Pen Blanks?!

Mini pinecone pen blanks are my favorite pen blanks I've ever made, and my blue and white sweet gum pod rollerball is one of my favorite pens. Both are natural inclusions: you're not casting a solid piece of wood, you're casting resin into and around something full of crevices and air. When it works, the resin gets in between all the little petals of the pinecone, and it really makes them pop.

In this guide I'll walk you through how I do it: stabilizing sweet gum pods with Cactus Juice in a mason jar, holding pinecones down so they stay put, mixing and swirling Alumilite, curing in a pressure pot, cutting the blanks, and a few notes on turning and finishing them so they don't chip out.

Video: Mini Pinecones & Alumilite Pen Blanks?!
Mini Pinecones & Alumilite Pen Blanks?!

What you need

For stabilizing the sweet gum pods

  • Sweet gum pods
  • Stabilizing resin. I use Cactus Juice from TurnTex.
  • A mason jar with a vacuum lid (mine is a lid from TurnTex that fits a range of jar sizes), or a vacuum chamber
  • A vacuum pump
  • Tin foil
  • A toaster oven and an oven thermometer
  • A funnel, for pouring leftover Cactus Juice back into its container

For casting

  • Mini pinecones and/or stabilized sweet gum pods
  • A mold
  • A hot glue gun, for holding pinecones down in the mold
  • Alumilite resin (Part A and Part B)
  • A scale that reads to a tenth of a gram
  • Alumilite dyes and Pearl Ex powders. I've used interference blue and interference green Pearl Ex, blue, green and white dye.
  • Mixing cups and barbecue skewers
  • A small level
  • A pressure pot
  • A table saw for cutting the blanks

Step by step

Part 1: Stabilizing the sweet gum pods

  1. Soak the pods under vacuum. Sweet gum pods are mostly air, so I stabilize them with Cactus Juice before casting. Stabilizing pulls the air out under vacuum, lets resin soak into those empty spaces, then you cure the resin with heat.
    • Put the pods in the mason jar and fill it with Cactus Juice until it's above the pods.
    • Put the vacuum lid on and pull a vacuum. Watch the bubbles: you don't want them to reach the top of your jar or chamber. I had room to spare because I wasn't using the whole jar.
    • I ran the vacuum for about five or six hours. Then I turned it off and let the pods soak overnight, about ten or eleven hours.
    • Read the instructions that come with Cactus Juice. They're great, and there's a lot more information on the TurnTex website.
  2. Drain, wrap and cure the pods. This is the tedious part.
    • Take the pods out one at a time and let them drip back into the jar. Cactus Juice is reusable, so I save all the leftover and funnel it back into the jar.
    • Preheat the toaster oven to 200 degrees Fahrenheit. Use a thermometer so you know what temperature it's really at.
    • Wrap each pod in its own little ball of tin foil. In the past I rolled them up and tried to keep them separated so they didn't stick together. Wrapping each one takes a lot longer, but I was happy with the results.
    • Bake them. It takes a couple of hours to three hours, depending on the material. You can tell they're ready when the juice that bleeds out of them is solid.
    • The whole process is a waiting game, and it doesn't hurt to wait longer on any part of it.
Video: Stabilizing Sweet Gum Pods In A Mason Jar
Stabilizing Sweet Gum Pods In A Mason Jar

Part 2: Casting the blanks

  1. Prepare the pinecones. I glue the mini pinecones down in the mold with a hot glue gun so they can't float. I wasn't sure whether they would float, since they're porous, and I wanted to be safe rather than sorry. Use small drops of glue. On one blank I used too much, and it left a deep spot that I had to fill later (see Common problems).
  2. Load the sweet gum pods. I use as many pods as I can fit, so they take up most of the mold. My sweet gum pods have never had a problem floating.
  3. Measure the Alumilite by weight. Alumilite is a polyurethane resin. You mix Part A and Part B by weight, not by volume. I use a scale that measures to a tenth of a gram, and even with larger batches it's important to be as exact as you can.
  4. Mix one batch, then split it for colors. I normally mix two separate cups. For the pinecones I mixed one big cup and split it into two after it was completely mixed. It's easier and probably faster.
    • For the blue and white pinecones I used interference blue Pearl Ex with a little blue dye in one cup, and white dye in the other.
    • The Alumilite green dye I use is really dark. One drop plus interference green Pearl Ex still came out really dark. The white swirls lightened it up enough that I was happy with it.
  5. Mix enough resin. I almost always forget how little actual material there is in sweet gum pods. They take more resin than you'd expect. On my blue and white batch I ran out and quickly mixed up roughly another 100 grams with white dye, and it worked out fine.
  6. Pour and swirl with a barbecue skewer. I pour both colors and move them around with a barbecue skewer. Popsicle sticks work too, and I've used them plenty, but a skewer is thin and long, so it gets into the crevices between the petals and pods. At the end I go back to the spots I didn't mix evenly and work in the last bits of color. Swirls are hard to get perfect with sweet gum pods because the pods take up so much of the mold, so don't expect a clean, even swirl.
Video: Alumilite & Sweet Gum Pod Swirl Pen Blanks
Alumilite & Sweet Gum Pod Swirl Pen Blanks

Part 3: Pressure pot and cutting

  1. Level the mold and pressurize.
    • Put the mold in the pressure pot and check it with a small level. With pours like these, where there's just enough resin, you don't want it to harden slanted, or part of your blanks won't be thick enough.
    • Clamp the lid down and pressurize. I always take my Harbor Freight pots to about 50 psi, and I've always had good results with that. My pot that's bolted to the table can go up to 80 psi, because its maximum is 90. The mini pinecones went in at 80 psi for a few hours.
    • Alumilite hardens in about two or three hours, but I usually take it out after four.
  2. Demold and cut the blanks. I cut them to size on the table saw. Take your time laying out the cuts. On my pinecone batch I made a mistake, and one blank ended up too thin at the end. I may use half of it for a one-piece pen. On the sweet gum pod batch I left the last blank extra thick on purpose, since it could make a nice little knife handle.
  3. Check them with denatured alcohol. Wipe a blank with denatured alcohol to see what it'll really look like. On the pinecones you can see that the resin got in between all the little petals.

Turning and finishing

I've heard from a lot of people that sweet gum pod blanks chip out and have to be turned with really light cuts. On my sweet gum pod fountain pen I took aggressive cuts, with tools that weren't as sharp as they should have been. I only had one or two really small chips. I don't normally turn that aggressively; I did it to show how little it chipped.

My finish on these:

  1. Rough the blank with a carbide tool, then sand from about 120 up to 600 grit before any finish goes on. Since the CA finish is basically a shell, I think it looks better over a polished surface.
  2. Clean off the dust with denatured alcohol and let it dry.
  3. Apply a couple of coats of thin CA (I use Stick Fast) with no accelerator, so it soaks into the voids and imperfections. That's especially important with sweet gum pods. I got that tip from Zack Higgins.
  4. Switch to thick CA and use a few sprays of accelerator. The thick coats give you enough build that you won't sand through the finish.
  5. Sand with Micro-Mesh from 600 up to 12,000, then polish with HUT Ultra Gloss on a microfiber cloth.
Video: Sweet Gum Pod & Alumilite Rollerball Pen
Sweet Gum Pod & Alumilite Rollerball Pen

Common problems and fixes

A deep spot where the hot glue was

Too much hot glue holding a pinecone down leaves a pocket once you demold. On my pinecone fountain pen I filled it with shavings and CA glue. It came out looking a bit white; dark wood shavings would have been best. It ended up looking fine, I lined the pen clip up over it when I pressed the pen together, and you can't feel it under the CA finish. Better fix: use less glue.

Running out of resin mid-pour

Sweet gum pods have very little solid material, so they take a lot of resin. If you run short, quickly mix a small batch in one of your colors and keep going.

Green that comes out too dark

One drop of Alumilite green dye made my batch really dark. Mixing a larger batch so one drop goes further is one way around it. The white swirl also lightens it.

Blanks too thin on one end

That's either the mold hardening on a slant or a mistake when cutting. Level the mold in the pot, and lay out your saw cuts carefully.

Pods sticking together in the oven

Wrap each stabilized pod in its own ball of tin foil before baking.

Chip-out when turning

My stabilized and cast sweet gum pod blank had almost no chip-out, even with aggressive cuts. When finishing, let thin CA with no accelerator soak into the voids before you build up the finish with thick CA.

FAQ

Do you have to stabilize sweet gum pods before casting them?

I do. All my sweet gum pods are stabilized with Cactus Juice before I cast them in Alumilite. They're mostly air, and stabilizing fills those pockets with resin that's cured by heat.

Can you stabilize without a vacuum chamber?

Yes. I stabilized these in a mason jar with a vacuum lid from TurnTex, which works on any jar in its size range. My mason jar came from Target.

Do pinecones or sweet gum pods float in resin?

My sweet gum pods have never floated. I wasn't sure about pinecones because they're porous, so I hot glued them to the mold to be safe, and it worked perfectly.

What pressure do you use for pinecone pen blanks?

I put my mini pinecone blanks in the pressure pot at 80 psi for a few hours. Only go that high in a pot rated for it; mine that I take to 80 has a maximum of 90. On my Harbor Freight pots I use about 50 psi and have always had good results.

Is Cactus Juice reusable?

Yes. Let the pods drip back into the jar and pour the leftover back in with a funnel.

What pen kits work with these blanks?

I've turned them into fountain pens and a Junior Gentleman's II rollerball. The gold parts on my pinecone fountain pen really complement the brown and gold of the pinecone.

If you'd rather skip straight to turning, my mini pinecone blue and white swirl pen blank and sweet gum pod pen blanks are the blanks I make the way I've shown here.

Products in this guide

← All guides