Casting Grapevine and Alumilite Pen Blanks
My hybrid grapevine pen blanks start as California grapevine. I stabilize it with Cactus Juice and cast it in colored Alumilite resin. Out of the mold you get a big block of plastic and wood, and you cut it up into blanks. I'm based in Sonoma County, so these are my Sonoma pen blanks.
This guide walks through my whole process from my casting videos: stabilizing the grapevine, mixing and coloring the resin, pouring, pressure, and cutting the block into blanks. I've included the mistakes I made along the way so you can skip them.
What you need
For stabilizing
- Sandblasted grapevine. I buy mine from a supplier that sandblasts it, which takes off all the bark.
- Cactus Juice, the stabilizing resin I use.
- A vacuum chamber and vacuum pump. My chamber is a big Mason jar from Target.
- Weights to hold the wood under. I use scuba diving weights from a local dive shop (a 2.5 lb and a 5 lb). They're cheap and liquid-proof, so they don't soak anything up.
- An airtight container to keep the wood in after drying.
- Aluminum foil, paper towels, a utility knife and a toaster oven for curing.
For casting
- Alumilite, a polyurethane casting resin mixed by weight, Part A and Part B, and a scale to weigh it.
- Color: Alumilite dye and Pearl Ex powders (I use Interference Blue and Blue Russet in these videos), metallic gold powder, or gilding flakes (I use Nuvo gilding flakes in gold, silver and copper).
- Molds that Alumilite won't stick to. Mine are made from HDPE plastic, and I cover my whole casting table with it too, so cleanup is easy.
- A popsicle stick or barbecue skewer for swirling, and a mold rack.
- A pressure pot.
- A table saw to cut the block into blanks, and denatured alcohol to wipe them down.
Step by step
Part 1: Stabilizing the grapevine
Stabilizing makes the wood harder, makes sure there's no moisture in it (important when you're casting it in resin), and brings out the grain. All the grapevine in my blanks is stabilized with Cactus Juice before it's cast.
- Dry the wood first. You have to dry the wood before you stabilize it. Once mine is dry, I keep it in an airtight container until it goes in the chamber.
- Load the chamber. Pack the grapevine into the vacuum chamber and put the weights on top so nothing floats.
- Fill with Cactus Juice. Fill it a little past the highest piece of grapevine. As the vacuum pulls air out, there has to be enough Cactus Juice left to soak in and impregnate the wood.
- Pull vacuum slowly. With the chamber this full, closing the valve all the way at once makes it bubble up so much that Cactus Juice gets into the air line and into the vacuum pump. So I bleed the air valve: let a little air in, close it, and keep doing that until I can finally hold full vacuum.
- Wait for the bubbles to stop. Once at full vacuum, I just let it sit. It's done a few hours later, when there are no more little bubbles coming up.
- Preheat the toaster oven. I set it to 200°F; anywhere between 190°F and 200°F is fine. Have it preheating while you unload, because you want the wood in the oven as soon as possible after it comes out of the Cactus Juice.
- Drip and wipe every piece. Let each piece drip off as much Cactus Juice as you can (to save it), then wipe every single piece with a paper towel. Grapevine isn't as easy as a square blank to clean up later with a saw or sander, so getting the outside clean now keeps down crystallization from juice that bleeds out while it cures.
- Wrap and cure. Wrap the pieces in foil packs and put them in the toaster oven for a couple of hours. It depends on the batch: thicker grapevine takes longer.
- Scrape the bleed-out while it's warm. This is the most important part for me. Take out one foil pack at a time and leave the oven on. The Cactus Juice inside the wood is already hard, but the bleed-out on the surface is still soft, and it hardens about a minute or two after it comes out. Work fast and scrape it off with a utility knife. Some pieces bleed out more than others. Done this way there's pretty much no bleed-out left, and what little there is won't show once it's cast.
Part 2: Mixing and coloring the Alumilite
- Weigh Part A and Part B. Alumilite is measured by weight, not volume.
- Mix until clear. Mix until there are no striations. Bubbles aren't a problem at this stage because the resin is going under pressure.
- Add color. Some examples from my videos:
- Blue and white swirl: blue and white, plus Interference Blue Pearl Ex, which adds color variations you can see under light, from blue to light blue.
- Pinot Red: a little red dye (not too much, so the powder can really shine) plus Blue Russet Pearl Ex. It doesn't sound like it from the name, but Blue Russet makes a beautiful deep burgundy.
- Molten lava: metallic gold powder plus Alumilite red dye.
- Gold, silver and copper leaf: gilding flakes in clear resin. Break the flakes into smaller pieces as you stir and as you add them. Use plenty of leaf so a turned pen isn't just clear.
Part 3: Pouring around the grapevine
- Set the grapevine in the mold. If a piece still has a little Cactus Juice bleed-out on it, put that side on top so it gets cut off later.
- Pour slowly. With a single color, how you pour doesn't matter much; just go slow to avoid air pockets. For swirls, put the colors in as evenly as you can, then go through with a popsicle stick or barbecue skewer and swirl.
- Use the extra. I keep a single-blank mold around for leftover resin so none goes to waste.
- Measure for the batch you're actually pouring. I usually pour both of my molds at once (10 blanks). In my first video I measured for five, then realized I was making 10. It ended up fine, but measure for the full batch.
Part 4: Pressure and curing
- Into the pressure pot. Put the molds on a mold rack and into the pressure pot. I put mine at 80 psi. I'm always impressed by how crystal clear Alumilite cures under pressure.
- Let it cure. My videos give different times here: "a few hours" in 2016, overnight for the Pinot Red batch in February 2017, and four hours for the molten lava batch in June 2017, which is the newest video that states a time.
Part 5: Demolding and cutting
- Demold. The block comes out pretty easily; sometimes I bang the mold on the floor to get it out. At this point it's just a big block of plastic and wood.
- Cut on the table saw. I cut them to about 3/4 inch square, and longer if I can trim the tops and I poured a little thick. Then square them up and clean them.
- Wipe them down. I wipe the blanks with denatured alcohol so you can see how they'll shine. It's not the same as a polished pen, but it's a better reference than a dry blank. In my 2021 video I sprayed a clear top coat instead to make them look wet for photos.
Common problems and fixes
Cactus Juice foams into the vacuum line
The chamber is too full to pull vacuum all at once. Bleed the air valve: let a little air in, close it, and repeat until it holds full vacuum without bubbling up.
Hard, crusty bleed-out on the grapevine
Wipe every piece with a paper towel before it goes in the oven, get it in the oven quickly, and scrape the bleed-out with a knife while it's still warm, one foil pack at a time. Once it cools, about a minute or two, it's hard.
Leaf flakes won't flow around the grapevine
This was my mistake the first time I cast leaf with grapevine. With a lot of leaf in it, the resin isn't as thin anymore, so it doesn't flow around embedded pieces the way it does in a plain block. I had to add more resin and move the leaf around by hand. Pour carefully and expect it to be thicker. Same goes for pinecone or anything else you embed.
Ran short on resin
Measure for the full batch before you start. If you end up with extra, pour it into a single-blank mold.
Bubbles in the resin
Mix until clear and pour slowly. Bubbles from mixing aren't a problem because the resin cures under pressure in the pressure pot.
FAQ
Do you have to stabilize grapevine before casting it in resin?
I always do. Stabilizing with Cactus Juice makes the wood harder, makes sure there's no moisture in it, and brings out the grain. Every grapevine blank I sell is stabilized before it's cast.
What resin is best for grapevine pen blanks?
Alumilite is my go-to. It's a polyurethane resin, and the general consensus in the pen turning community is that it's pretty good for pen blanks. It polishes up very nicely. Polyester resin is used a lot for pen blanks too, but it's not as high quality as Alumilite when it comes to turning.
How long does stabilized grapevine stay in the oven?
A couple of hours at 190°F to 200°F in my toaster oven. It depends on the batch; thicker grapevine takes longer.
Why cast grapevine pen blanks in a pressure pot?
Pressure takes care of bubbles, so I don't have to worry about them when mixing, and Alumilite cures crystal clear under pressure. I run mine at 80 psi.
What size are your grapevine pen blanks?
I cut them to about 3/4 inch square. Length varies a little by batch: my black and white swirl blanks are 5.5 inches long and my Sonoma Coast sea foam blanks are 5.25 inches.
Shop the blanks
If you'd rather turn than cast, my stabilized grapevine blanks are below, including the swirl colors, Pinot Red, black and white swirl, and Sonoma Coast sea foam. When you're ready to turn one, see my guide on how to turn a hybrid pen blank.




