Sale: 20% off everything through Dec 1
Wine Country Woodworks

Molds for Resin Casting Pen Blanks: Reusable HDPE Molds, Silicone Molds and Mold Racks

By Casey Martin · Updated

Video: How To Make Reusable Molds for Resin Casting (Non-Stick HDPE)
How To Make Reusable Molds for Resin Casting (Non-Stick HDPE)

Almost every week someone asks me how I make my molds, so this guide puts it all in one place. All of my own molds for resin casting pen blanks and bigger blocks are made from HDPE plastic, screwed together so one end comes off for demolding. I also use bought silicone block molds for certain blanks, and my molds go into the pressure pot on mold racks.

By the end you'll be able to size and build a square, reusable HDPE mold, know when a silicone block mold is the better choice, and build a mold rack that fits your pressure pot and keeps your molds level.

Video: How To Make Reusable Molds for Resin Casting (Non-Stick HDPE)
How To Make Reusable Molds for Resin Casting (Non-Stick HDPE)

What you need

For HDPE molds

  • HDPE plastic sheet. I buy mine on Amazon (the link is in the video description).
  • Wood screws. Any home center has them; the type I use is linked in the video description.
  • A table saw to cut the pieces
  • Clamps
  • A drill, a pilot bit and a countersink
  • A scrap of plywood for a spacer, if your walls want to bow

For mold racks

  • Plywood for the sides, and melamine for the shelves (the levels)
  • Scrap trim for the side pieces (mine is about 3/4 inch)
  • A bandsaw (or whatever works for you) to cut the corners of the levels
  • Screws, a drill and a pilot bit
  • A handle: I use a strap from a broken reusable grocery bag, plus some glue

Step by step: building a reusable HDPE mold

  1. Work out your dimensions from the bottom piece.
    • The bottom piece is the length you want your block to be, and the width you want plus the thickness of both side walls.
    • That's because the sides sit on top of the bottom piece and get screwed in from underneath. Screwing up through the bottom keeps the walls as perpendicular to the base as possible.
    • For reference, my larger mold makes a 3-inch-square block 7 inches long, so its bottom is 7 inches long and 3 inches plus two wall thicknesses wide. I have smaller ones and pen blank molds made the same way.
  2. Cut the pieces, and make the sides tall.
    • For the mold in the video I cut three identical pieces, 5 inches wide by 6 inches long: one bottom and two sides. With the two sides on, that leaves a 4-inch cavity, 6 inches long. Then the two ends go on.
    • The sides are a lot taller than the 4 inches I need. I end up with about 5 1/2 inches of clearance. That extra height gives room for anything that sticks up above the pour, like grapevine or burl you're embedding.
    • The tall sides also help when demolding: they give you something to tap against the ground to knock the block out. If you have the space, I highly recommend it.
  3. Clamp it so you can still adjust it.
    • A trick I learned after making quite a few of these: clamp just enough to have some tension, but so you can still move the pieces by hand.
    • Get everything flush along the sides and the ends, then tighten the clamp all the way so nothing moves while you drill.
  4. Pre-drill and countersink from the bottom, without melting the plastic.
    • HDPE heats up and melts if you drill for too long. Drill a bit, pull the bit out before the plastic starts melting, then keep going.
    • If you don't, melted plastic builds up in the crease, the pieces won't sit flush any more, and you'll have to take it apart and scrape it out with a knife.
    • Countersink every screw so the mold still sits level when it's finished.
    • I put the outer screws in first without fully tightening them, so nothing shifts when the clamp comes off and I drive the middle screw. Then do the other side the same way.
  5. Keep the walls square while you attach the ends.
    • If a side is bowing in a little (it shouldn't, but it happens), cut a piece of plywood or any scrap to your inside width, 4 inches in this case, and put it inside the mold.
    • Make the spacer shorter than the inside length so you can still put the ends on. It holds the walls perfectly perpendicular while you screw the ends in.
  6. Check for gaps and pick your removable end.
    • After driving the end screws, take a close look inside. If a table saw cut wasn't perfectly clean, you'll see a small gap at the corner.
    • Drive another screw right where the gap is. Then make the other end the one you take off each time.
    • Sometimes it looks like a gap inside but the outside is completely sealed, because the cut is ever so slightly slanted. That's fine: resin won't leak, you just get a little fuzz on the end of the block.

Step by step: silicone block molds

Video: Shopisode 16 - Mold Racks, 20 lbs of Silicone, Molds, & More
Shopisode 16 - Mold Racks, 20 lbs of Silicone, Molds, & More
  1. Use them for blanks that are mostly resin.
    • I started using block molds from PTownSubbie for a few blanks I keep in stock. Each one gives me seven 3/4-inch-square blocks.
    • They work great for anything that's mainly resin: gold leaf, silver leaf, money blanks and colored pencil blanks. When I'm embedding something that sticks up, like grapevine or burl, the tall sides of my HDPE molds give it room.
  2. Support the bottom completely flat.
    • The one thing you have to get right with these molds is that the bottom is supported completely flat, so the blocks don't come out with a curve on the bottom.
    • I used to set them on a piece of scrap HDPE, but it was basically impossible to stack anything on top without leaving an indentation in what's in the mold. A mold rack with flat shelves fixes that (see the next section).
  3. Making your own silicone molds.
    • I've made a silicone mold of a piece of live-edge maple burl. The idea is to cast a resin "burl" in an opaque color, then put it in one of my block molds and pour something clear over it. I degassed the silicone in my vacuum chamber.
    • I'm not an expert with silicone, so I'm not going to give you a recipe here. Follow the instructions on your silicone kit.

Step by step: building a mold rack for your pressure pot

Video: Mold Racks for Resin Casting
Mold Racks for Resin Casting
  1. Cut the levels.
    • My racks have three levels, each about 7 1/4 by 7 1/4 inches (that's just the shelf, not counting the sides).
    • Cut all three, tape them together, and cut the corners on the bandsaw so they match.
    • Use melamine for the levels if you can. Resin will stick to the rack sooner or later, and with melamine you can pop a stuck piece of Alumilite off with a utility knife. On plywood you can still get it off, it just takes a lot longer. Keeping the shelves clean matters because a mold sitting on a lump won't sit level.
  2. Add the sides.
    • The sides can be any width. Mine are scrap trim about 3/4 inch thick, which makes the finished racks about 8 to 8 3/4 inches wide.
    • Two of my racks are about 7 3/4 inches tall. The third is 7 1/4 inches without the sides and 8 1/2 inches with them. Taller racks mean more room for molds.
    • Pre-drill, and use just two screws into each level. Don't screw them in super hard, so nothing splits.
    • Build the rack lying on its side on a level surface. Everything stays parallel and perpendicular, so the molds sit level and the resin cures level.
  3. Add a handle that folds flat.
    • I used a strap from a broken reusable grocery bag. Those straps are really sturdy. I glued it down for extra support and screwed it in.
    • I can carry the full rack and it stays level, then I tuck the strap down and put the lid on.
    • A rigid handle that stands up needs extra space so the pressure pot lid doesn't hit it. A fold-flat strap takes up no room, so I get more space for molds.
  4. Or buy a rack with removable shelves.
    • I also use a rack from PTownSubbie, made for the common 2 1/2-gallon pressure pots (Harbor Freight, TCP, California Air Tools).
    • Its shelves are removable: I can use all of them for the silicone block molds, or take one out and fit my taller pen blank molds.
    • I got a big one for my 5-gallon pot too. When I'm doing several batches at once, I can put a blast shield on top so filling the pot with air quickly won't splatter the resin, with flat HDPE on the bottom to stack from.

Which approach is newer: my homemade racks are from 2017. In 2019 I started using bought racks with removable shelves, mainly because they give my silicone block molds a flat, stackable shelf. The homemade racks still work, and the building tips above still apply if you'd rather make your own. Curtis Seebeck at TurnTex Woodworks has detailed plans for a rack very similar to mine.

Common problems and fixes

The HDPE pieces won't sit flush after drilling

The drill melted the plastic and it built up in the crease. Take it apart, scrape it clean with a knife, and next time pull the bit out every so often, before the plastic starts melting.

A wall is bowing in

Put a plywood spacer cut to the inside width in the mold while you attach the ends.

There's a gap at a corner

Drive another screw at the gap and don't use that end as your removable end. If the outside is sealed and the gap is only on the inside, it's fine; you'll just get a little fuzz on the end of the block.

The block is stuck in the mold

Take the screws out of the removable end and tap the tall sides against the ground to knock the block out.

Blocks from silicone molds have a curved bottom

The mold wasn't supported flat. Set it on a flat, rigid shelf, and don't stack anything directly on a soft mold.

Molds sit crooked in the rack

Either the rack wasn't built square or there's cured resin stuck on a shelf. Build racks on their side on a level surface, and scrape shelves clean (melamine makes this easy).

FAQ

What are the best molds for resin casting pen blanks?

For me it's both. Homemade HDPE molds, with tall sides for wood like grapevine or burl that sticks up, and silicone block molds for blanks that are mainly resin, like gold leaf, silver leaf, money and colored pencil blanks.

Are HDPE molds reusable?

Yes. They're non-stick, so I take the screws out of one end, knock the block out, screw the end back on and use the mold again.

How do I size an HDPE mold?

Start with the bottom piece: the length you want, and the width you want plus both wall thicknesses. Make the sides taller than the pour so you have room for wood that sticks up and something to tap on when demolding.

Can I make molds out of melamine?

You can, but it's not the best material for molds. I use it for mold rack shelves, because cured resin pops off it easily.

Why do I need a mold rack?

It lets you stack several molds in the pressure pot, carry them in and out level, and give silicone molds the flat support they need.

A non-stick silicone mat is handy too. Nothing sticks to it, so it's an easy surface to work on with resin.

And if you'd rather turn than cast, my finished pen blanks are in the shop, and the Alumilite casting tips guide covers the pour itself.

Products in this guide

← All guides