Sale: 20% off everything through Dec 1
Wine Country Woodworks

How to Cast Gold Leaf, Copper Leaf and Shredded Money Pen Blanks

By Casey Martin · Updated

Video: Resin Casting Alumilite & Gold Leaf, Copper Leaf, and Silver Leaf with Grapevine for Pen Blanks
Resin Casting Alumilite & Gold Leaf, Copper Leaf, and Silver Leaf with Grapevine for Pen Blanks

Gold leaf pen blanks are some of my favorite blanks. They're just crystal clear Alumilite with gold, silver or copper leaf flakes all through it. Once one is turned and polished, it almost looks like a vial full of gold leaf. I've also cast money pen blanks with real shredded US money and gold leaf. You can read the little numbers and words on the shreds right through the resin.

This guide puts together what I've learned over several videos: how to get the leaf into the resin, how much to use, how I pressure and cut the blanks, the mistakes I've made, and how I finished a shredded money blank on the lathe.

Video: Resin Casting Alumilite & Gold Leaf, Copper Leaf, and Silver Leaf with Grapevine for Pen Blanks
Resin Casting Alumilite & Gold Leaf, Copper Leaf, and Silver Leaf with Grapevine for Pen Blanks

What you need

  • Clear Alumilite resin. It's my go-to resin: a polyurethane resin, part A and part B, mixed by weight at a 1 to 1 ratio. I use it with no dye for these because it cures crystal clear under pressure. Alumilite says it's optically graded, meaning it's clear enough to be used for glasses.
  • Metal leaf flakes. I use Nuvo gilding flakes in gold, silver and copper.
  • Shredded US money for money pen blanks (more on where it comes from below).
  • A scale for weighing the resin, mixing cups and stir sticks. A popsicle stick is handy for pushing leaf down in the mold.
  • Pen blank molds.
  • A pressure pot. I pressurize these at 80 psi.
  • A table saw for cutting the cast block into blanks.
  • Denatured alcohol for wiping the blanks down, and a clear spray finish or lacquer if you want to show off the wet look before turning.
  • Optional: grapevine or another item to embed with the leaf.

Step by step: casting gold, silver and copper leaf pen blanks

  1. Weigh and mix the Alumilite.
    • Weigh out part A and part B by weight.
    • Mix until it's perfectly clear: no cloudiness and no striations (the little lines you see when you stir). If those are gone, it should cure perfectly clear.
    • Take extra care here. When you add dye you get to stir everything a second time, but with clear resin this is your only real stir, so I make sure it's absolutely perfect.
    • If your cups aren't big enough for a full mold, split the resin into several cups. For one batch I used four cups: two for silver and two for gold.
  2. Stir the leaf into the resin in the cup.
    • Add the flakes to the mixed resin and stir them in.
    • The biggest thing is breaking the flakes down into smaller flakes, both while you're putting them in and while you're stirring.
    • Add a lot of leaf. You want enough that when you turn a pen down it isn't just completely clear in spots.
    • For a combination blank, I mix gold, silver and copper together. That combo is my favorite look, then gold, then copper, then silver.
  3. Pour into the mold. Pour the leaf-filled resin into the mold. Stirring the leaf in first gives you that dense but still spread-apart look I really like.
  4. Work fast and get it under pressure. With a big batch of resin it starts getting hot really quickly, so I move fast and get it into the pressure pot as soon as possible. With crystal clear Alumilite it's especially important that it gets pressurized properly. I put mine in at 80 psi and let it sit overnight.
  5. Demold and cut. Each mold comes out as one big block. I cut the blocks into blanks on the table saw, about 3/4 inch square. If I poured a little thick, I can leave them a little bigger. Sometimes I leave one blank extra wide rather than waste a cut-off.
  6. Clean and spray (optional). I wipe the blanks with denatured alcohol and spray a clear top coat or lacquer to give them the wet look. It's not as good as a real polish, but it gives you an idea of how clear the finished piece will be.
Video: Gold Leaf and Silver Leaf Alumilite Pen Blanks
Gold Leaf and Silver Leaf Alumilite Pen Blanks

What changed: leaf in the cup, not in the mold

In my 2018 video where I made a solid gold leaf block, I started stirring the leaf into the cup. It was finicky, so I switched to pouring the resin into the mold and putting the leaf in there. I'd take a pinch with my fingers, spread it all over, and push it down with a popsicle stick. A little over a month later I had changed my mind: I was wrong in thinking that was easier. Mixing the leaf into the resin in the cup and then pouring is much easier and gives a better look. I still did it that way in my 2021 grapevine leaf video.

One thing from that block video is still worth knowing: the leaf has pretty much the same density as Alumilite. It won't sink and it won't float to the top. That's good, but it also means it won't move to the bottom or the middle on its own. If you want it somewhere specific, you have to push it there.

Casting grapevine with gold, silver or copper leaf

I've made plain leaf blanks for years, but the first time I cast leaf around grapevine I made a mistake you can learn from. Once you add a lot of leaf, the resin isn't as thin anymore, so it doesn't flow around embedded pieces as easily. On some of my molds I had to go back, add more resin and move the leaf around by hand.

So if you're embedding grapevine, pinecone or anything else, be careful when you pour and expect the leaf resin to be thicker. After that it's the same as above: pressure pot, table saw and a spray of clear top coat.

Step by step: shredded money pen blanks

  1. Get the shredded money. The shredded money comes from the Federal Reserve. They're bills of any denomination with a printing error that makes them invalid to use. The Federal Reserve shreds them and sells bags of the shreds online for arts and crafts.
  2. Keep the resin clear. I use completely clear Alumilite with no dye because I think that shows off the shredded money and the gold leaf the most.
  3. Mix more resin than you think. The shredded money soaks up the resin, so it's really hard to judge how much you need. My second time ever casting it, I didn't mix enough and had to mix more and add it. Since it's clear resin, topping up is pretty easy.
  4. Add gold leaf. Gold leaf goes in with the money. Push it down so it isn't sitting right at the surface. I wish some of mine had been pushed down more, because the saw cut some of it off.
  5. Pressure. I used my biggest pressure pot at 80 psi. I honestly don't know how much difference there is between 45 and 80 psi, but since I was going for crystal clear I used what I had.
  6. Cut and check. Cut the blanks to size on the table saw. Fresh off the saw they're very smooth, and a wipe of denatured alcohol gives you an idea of how clear they are. You only see the full clarity once they're finished with something that makes them look wet, like a CA or wax finish.
Video: U.S. Money, Gold Leaf, & Crystal Clear Alumilite Pen Blanks
U.S. Money, Gold Leaf, & Crystal Clear Alumilite Pen Blanks

Turning and finishing a money and gold leaf blank

I turned one of my shredded money and gold leaf blanks into a letter opener from a Penn State Industries kit. Preparing the blank is pretty much the same as preparing a pen:

  1. Drill the blank and scratch up the brass tube so the super glue has better adhesion.
  2. Glue in the tube with super glue and hit it with accelerator.
  3. Barrel trim on the drill press so the tube is flush.
  4. Turn on the lathe down to the bushings, and sand to 600 grit.
  5. Clean with denatured alcohol to get ready for a CA finish.
  6. CA finish. One coat of thin CA first. It dries so fast and gets into the pores, so I don't need accelerator. Then two or three coats of medium CA with accelerator.
  7. Polish. Sand with micromesh, then polish with HUT Ultra Gloss on a microfiber cloth and buff it off.

After polishing you can see the little numbers and words on the shreds, and the brass tube really brings out the gold.

Video: Making A $1,000 Letter Opener Made of GOLD & MONEY?!
Making A $1,000 Letter Opener Made of GOLD & MONEY?!

Common problems and fixes

The leaf is finicky to mix in

Break the flakes into smaller pieces as you add them and as you stir.

Clear patches when you turn the blank down

Not enough leaf. Add a lot of leaf so the turned blank isn't completely clear in spots.

Leaf resin won't flow around grapevine or other embedded pieces

Resin with lots of leaf in it is thicker. Be careful when you pour. If it still doesn't fill, add more resin and move the leaf around by hand before it goes in the pot.

Not enough resin for the money

Shredded money soaks up resin. Mix extra, or be ready to mix a second batch and top up before pressurizing.

Gold leaf cut off at the surface

Leaf doesn't sink, so it stays at the top if that's where it lands. Push it down into the blank before pressure so the saw doesn't cut it off.

The batch is getting hot

Big batches of resin heat up fast. Have everything ready, work quickly and get the molds into the pressure pot as soon as possible.

Off-center drilling on a long blank

When I made a bottle stopper from a gold leaf blank, I drilled ever so slightly off parallel with the blank, and on a long piece that meant I had to turn the end really thin. Make sure you drill parallel with the blank.

FAQ

What leaf do you use in gold leaf pen blanks?

I use Nuvo gilding flakes in gold, silver and copper, cast in clear Alumilite with no dye.

Does gold leaf sink or float in resin?

In Alumilite it does neither. Its density is pretty much the same as the resin, so it stays where you put it. That's why I stir it into the resin before pouring instead of hoping it settles. Mica flakes are different: they're denser than Alumilite and sink to the bottom.

Is a copper leaf pen blank the same as rose gold?

Some people call the copper leaf rose gold. I call it copper, but the names are pretty interchangeable.

Is it legal to put shredded money in a pen blank?

The shredded money I use comes from the Federal Reserve. They shred misprinted bills that can't be used and sell bags of the shreds online for arts and crafts.

What pressure and how long in the pressure pot?

I put my leaf and money blanks in at 80 psi and leave them overnight. Four hours is the minimum I'd recommend before taking any Alumilite out to cut or turn it.

What pen kit plating goes with gold or silver leaf?

Brass tubes go with gold leaf, and nickel-plated tubes go with silver. On my money and gold leaf letter opener, the brass tube really brought out the gold.

Get the blanks

If you'd rather skip the casting and go straight to turning, I make all of these blanks myself: gold, silver and copper leaf, grapevine with leaf, and shredded money with gold leaf.

Products in this guide

← All guides