Sale: 20% off everything through Dec 1
Wine Country Woodworks

Finishing Resin and Wood Pen Blanks: Choosing and Applying the Best Finish

By Casey Martin · Updated

Video: Finishes for Resin + Wood
Finishes for Resin + Wood

"What's the best finish for resin and wood?" is a question I get all the time. The honest answer is that there isn't one perfect finish. It depends on what you want the finished piece to look and feel like. In this guide I'll walk you through the finishes I actually use on hybrid pens and blanks, what each one is good at, and how I apply them, so you can pick the right one for your next project.

By the end you'll know when to reach for a CA glue finish, when a plastic polish or a paste polish makes more sense, how I buff blocks to a high gloss off the lathe, and the quick tricks I use to make raw blanks look good in photos.

What you need

You won't need all of this. Pick the items for the finish you choose in step 1.

  • For any turned pen: sharp tools and sandpaper, plus micro mesh pads for wet sanding up to a very high grit.
  • CA glue finish: a good CA glue, applied on the lathe.
  • Plastic polish: a one-step friction polish for plastics. I started with the one-step plastic polish from Penn State Industries and now use HUT Ultra Gloss. They work about the same.
  • Paste (friction) polish for wood and resin: a multi-step paste like the wood-and-resin paste I tested, or EEE-Ultra Shine.
  • Small cloth pieces for applying polish on the lathe (small, not large rags).
  • For blocks and other off-lathe pieces: sandpaper up to 2,000 grit and a buffing setup. I use the Beall three-wheel buffing system: Tripoli, white diamond and carnauba wax.
  • For photos of raw blanks: boiled linseed oil and paper towels, or an acrylic spray finish plus a respirator if you're spraying indoors.

Step by step

  1. Decide how you want the pen to look and feel.
    • Want the same gloss across the wood and the resin? Use a CA glue finish (step 3). Because you're putting a layer over the whole pen and polishing that layer, the sheen is the same everywhere.
    • Want to feel the wood? Use a paste polish (step 5). You'll never get a CA finish to feel like wood. If you turned a coffee bean pen and want to smell the coffee beans, a CA finish isn't an option either.
    • Is the blank all resin, with no wood? Skip CA and go straight to a plastic polish (step 4).
    • Finishing a block, bowl or something else that fits in your hand? I buff those (see the off-the-lathe section below).
  2. Get the surface right before any finish (pen blank sanding).
    • Start with sharp tools. A sharp carbide cutter can leave the resin with a little shine right off the tool. On the grapevine hybrid in the video below, it was close to a 300-grit sanded surface on the resin, with no tear out. When the tools do that, you can start sanding at a higher grit.
    • The wood will always come off the tool a bit rougher than the resin.
    • For a polish finish, I wet sand with micro mesh up to a really high grit. If you want a perfect finish, you have to do the sanding first.
  3. Option A: CA glue finish, then polish.
    • Apply the CA on the lathe. A lot of my turning videos show how I do it, and it's pretty straightforward. See the hybrid pen turning guide for the whole turning process.
    • Then polish the CA layer. The plastic polish works here because you're polishing the CA, not bare wood.
    • What you get: a very hard, super durable finish that's crystal clear if you apply and polish it correctly with a good CA glue. It's waterproof too, as long as you seal the ends of the project.
    • Don't put CA on an all-resin pen. You're just putting another layer of plastic on top of plastic, so it's pointless.
  4. Option B: All-resin pens, plastic polish.
    • Wet sand with micro mesh up to a really high grit.
    • Wipe the polish on with a small piece of cloth while the lathe is spinning. I used to use bigger rags, but now I cut them into small pieces to be safer.
    • The polish makes the resin really shiny and takes out the micro scratches.
    • Don't use plastic polish on bare wood in a hybrid. It's made for plastic and won't bring the wood up to a high sheen, so the resin and the wood will shine unevenly. On a hybrid, only use it over a CA finish.
  5. Option C: Paste (friction) polish for wood and resin.
    • Move the tool rest out of the way. Put a little paste on the spinning blank. You need less than you'd think. I used way too much in the video.
    • Spread it on like any friction polish, rub it in with the lathe running, then buff it out. It makes the colors pop right away.
    • Do the same with each finer step. The paste I tested started as a wood paste plus a two-step acrylic polish (the bottles look the same except for the caps, so don't mix them up). By the time I made my finishes video, it was four steps. The last two steps take it to a very fine grit, which takes the micro scratches out of the resin the same way a plastic polish does.
    • The paste maker recommends a sanding sealer before the first step for things like bowls. I skipped it on this pen to keep things quick.
    • What you get: a glassy finish on the resin, and wood that pops but isn't a gloss finish. The difference in sheen between wood and resin never fully goes away. I think it's impossible to avoid unless you use something that builds a layer, like CA or polyurethane. But if you want to feel the wood, this is the best bet for a turned project. It's also much easier and less complicated than a CA finish.
    • Open-grained, hard woods are tougher to shine without CA. The grapevine in the video below is one of them.
Video: Testing Chinese Turning Tools & A New Wood/Resin Finish
Testing Chinese Turning Tools & A New Wood/Resin Finish

Finishing blocks and raw blanks off the lathe

  1. Blocks and handheld pieces: sand to 2,000 and buff.
    • This is how I finish my blocks for display. I'd recommend it for anything small enough to hold in your hand, even a wood-and-resin bowl or an all-resin bowl. It's the best way I've found to polish resin to a crystal-clear, high gloss.
    • Sand up to 2,000 grit. Then buff on the Tripoli wheel, then the white diamond wheel.
    • Skip the carnauba wax wheel on resin. The resin is harder than the wax, so the wax adds no real protection. It just gives you something a fingernail can scrape, and then the finish doesn't look as good. Carnauba is really meant for wood.
    • A buffed finish looks the same forever, as long as you don't scratch it.
  2. Raw blanks, just for photos: use oil or acrylic spray.
    • Wiping boiled linseed oil on with a paper towel makes a blank look wet and hides scratches. It's perfect for photos, but it only looks that good for about 20 to 30 minutes, until the oil starts to dry. That's fine for my blocks because they'll be cut up anyway. I don't have much experience using it as a regular finish.
    • Pen blanks are too small for oil to be practical. I used to use Deft spray lacquer, but it only looked its best for the first 30 seconds to a minute while it was wet.
    • Now I use an acrylic spray. Straight off an 80-tooth table saw blade, the blanks look fantastic. Once it cures, it looks almost the same as it did wet. The difference is maybe 5 to 10 percent, and see-through blanks stay see-through. It takes a while to dry, so don't touch it or it'll be sticky. I'd guess about an hour to fully dry, but I've never really tested that.
    • Safety: the acrylic spray smells terrible. If you're inside, wear a respirator and really ventilate the area. I keep my garage door open.

Common problems and fixes

The resin is glossy but the wood looks dull

That's normal with a polish that doesn't build a layer. Plastic polish is the worst for this because it's only made for plastic. Switch to a wood-and-resin paste polish, or put a CA finish over the whole pen and polish that. To get a truly even sheen you need something that builds a layer, like CA or polyurethane.

Fine scratches still show in the resin

Go back and wet sand with micro mesh up to a high grit, then use a plastic polish or the finest steps of a paste polish. Both are made to remove micro scratches. Off the lathe, sand to 2,000 grit and buff.

The buffed resin gets scuffed easily

If you buffed on carnauba wax, that's probably what you're seeing. The wax is softer than the resin and scrapes off. On resin, stop after the white diamond wheel.

My photo finish stopped looking wet

Boiled linseed oil only looks wet for 20 to 30 minutes, and spray lacquer for under a minute. For photos that hold up, try an acrylic spray. For a piece you'll display, buff it or use a built-up finish like wipe-on poly.

The spray finish feels sticky

It isn't dry yet. Acrylic spray takes a while. Leave it alone (I'd guess about an hour) and work somewhere well ventilated.

FAQ

What is the best finish for resin and wood pens?

No finish is best for everything. A lot of people in the pen turning community swear by CA glue, and so do I: it's hard, durable, clear and has the same sheen across wood and resin. If you want to feel the wood, use a wood-and-resin paste polish instead.

Should I put a CA finish on an all-resin pen blank?

No. You'd just be putting plastic on top of plastic. Wet sand with micro mesh to a high grit and use a plastic polish.

Can I use plastic polish on a hybrid pen?

Only over a CA finish. On bare wood it won't give you a high sheen, and the wood and resin will look uneven.

How far should I sand resin before polishing?

On the lathe, I wet sand with micro mesh up to a really high grit before the plastic polish. For blocks I buff, I sand up to 2,000 grit first.

Is carnauba wax good on resin?

Not in my experience. The resin is harder than the wax, so it adds no protection and can get scraped by a fingernail. Save it for wood.

Can I use polyurethane or lacquer on wood and resin?

Yes. For larger projects that aren't on the lathe, like boards and tables, pretty much any finish works over resin: wipe-on poly, lacquer, shellac. Choose based on how much use the piece will see. If it needs to be food safe, use a food-safe finish that builds a thick enough layer.

If you want to try these finishes yourself, my grapevine and Alumilite hybrid blanks below are a good place to start. The gold, silver and copper leaf ones ship without a finish, so the choice is yours.

Products in this guide

← All guides