How to Make Color Swirl Pen Blanks with Mica Powder (Clean Color Separation)
People ask me a lot how to keep the colors in a color swirl pen blank from bleeding into each other. You want a red and a blue swirl to stay red and blue, not turn into a purple mess. This guide is the process I use to get clean color separation, first with dyes and then with mica powder, plus two variations I like a lot: galaxy resin blocks and glow in the dark pen blanks.
The short version: use opaque colors, let the resin warm up and thicken before you pour, pour lightly, and do the swirling with a thin stick at the very end. I use Alumilite Clear, but the technique works with other resins. The main difference is how long the resin takes to heat up.
What you need
- Resin. I use Alumilite Clear, a polyurethane resin mixed by weight. Any other resin works for this technique, it just warms up on a different schedule.
- Colorants. Alumilite dyes, mica powders, or both. Alumilite Clear on its own isn't opaque, so I add a little white dye to my colored cups (not the black) to make them opaque.
- A silicone mold. Mine is from P-Town Subby. It holds about 600 grams filled to its full one-inch height. I only fill it with about 540 to 550 grams since I don't need the full height, and because I cut my blanks to 3/4 inch I get seven blanks out of it.
- A small cup for each color, plus your main mixing cup.
- A temperature gun. Temperature is the main thing for color separation, so you need a quick way to check it.
- A barbecue skewer or popsicle stick for the final swirls. I like skewers because they're thin and give tight swirls.
- A pressure pot, ready to go before you start pouring.
Step by step
- Pick opaque colors.
- Opaque colors don't actually stop bleeding, but they give a much brighter contrast between swirls. You can do nice swirls with pearlescent powders, but opaque reads stronger.
- With Alumilite Clear, add a little white dye to each colored cup to make it opaque. In my original swirl video I did light purple, black, red and light blue, with white in every cup except the black.
- Weigh, mix and split the resin.
- Weigh out your total resin, mix it, and pour an equal amount into each color cup.
- In the video I added the dyes after splitting the resin. That way, if one cup is low, I can top it up from another without mixing colors.
- If time is tight (say I'm pouring two molds), I put the dyes and white in the cups first. The catch is you have to get each pour right the first time. You can also weigh each cup out individually.
- Mix the colors in and wait for the resin to heat up.
- This is where the color separation comes from. As the resin gets hotter it gets closer to curing and gets thicker. Thicker resin doesn't blend as easily when the colors meet.
- Check each cup with the temperature gun. In the video my resin started at about 84°F. At true room temperature it starts around 72°F.
- I start pouring at around 100 to 105°F. You can start as low as 95°F if you can still get to the pressure pot in time. In the video I poured at 106 to 107°F.
- With Alumilite Clear, working time in my shop runs from about 7 minutes to as much as 10 minutes when it's really cold.
- Pour slowly and lightly.
- At the start it's fine if the resin goes to the bottom, because you want each layer of the mold to get every color.
- As the mold fills, pour even more lightly. I shake or splatter the resin on so it sits on top instead of diving into the liquid below.
- Pouring hard and fast forces colors down into the body of the resin and mixes them on its own. You want the colors to go in as slowly and methodically as you can, and do the actual swirling at the end.
- Swirl once at the end.
- When the mold is full, make one final pass with a barbecue skewer or popsicle stick. The thin skewer gives tight swirls that still show up after it cures.
- Get it into the pressure pot fast.
- The highest you ever want the resin to be before it goes under pressure is about 120°F, to avoid bubbles. I started pouring at 107°F in the video, and it was probably getting pretty close to that by the time it went in the pot. That's why 100 to 105°F is about the max to start pouring a multi-color swirl.
- Above that, only do it if you're pouring two colors right in and swirling them right away. With lots of colors, that won't give you the best separation.
- Demold and cut. Usually you can't really tell how tight the swirls are until you cut into the casting. I cut mine on the table saw.
Using mica powder for color swirls
A lot of people don't realize you can swirl mica powders just like dyes. You follow the same process: wait for the resin to get hotter and thicker, then pour lightly and swirl.
- How much mica powder? It depends on the look. Add a lot and most mica powders go opaque. Add a little and you get a transparent tint with some pearlescent sparkle that you can't get from dye alone. Some, like macro pearl, are really tough to get fully opaque no matter how much you add.
- Mix mica powder with dye. If I want to be sure a color is opaque, so nobody has to paint their tubes, I add the matching Alumilite dye to the mica powder, for example Alumilite red dye with my Pinot Red mica, or blue dye with an ocean blue or sky blue mica. Every Alumilite dye except white pairs well with mica powder. It can't go completely opaque, because light has to get in for you to see the sparkle.
- Mix transparent and opaque powders. In one batch I used a transparent blue macro color shift powder with the more opaque interference blue and micro pearl. The transparent color lets light into the blank, which gives a lot of depth and lets the color shift and interference effects show.
- Bleeding looks different with mica. Red and blue dye dumped together in cool resin turns purple. Red and blue mica bleeds a little less, and where it does, it looks like a nebula of red and blue sparkles instead.
- Test the opacity at the final thickness. Your mixing cup is a lot deeper than the finished part. Pour a little colored resin into an empty cup to the thickness of your blank or turned part and hold it up to the light. If it's too see-through, add more powder or dye. You can always add more, but you can't take it out. Take notes so you can repeat colors you like.
Galaxy resin: let the density do the swirling
For galaxy resin blocks I don't swirl at all. I let the denser powder sink through the casting while it cures.
- Make a mostly clear base. Mix the resin in a big cup and pour a little off into two small cups before adding anything to the base. In the video I made a 3 x 3 x 7 inch block with sweet gum pods, which took about 38 ounces.
- Load the base with sparkle. I added silver holographic, white holographic, white blue holographic and green macro interference powders, a little at a time. None of these make it opaque. Mix, look, and add more until it looks like a galaxy.
- Make dense accent colors. In the small cups I mixed violet and sky blue pearl powders, enough to make them more opaque. Those denser, more opaque colors are the ones that sink.
- Pour, drop, and leave it. Pour in the base, drip a little of each accent color across the top, and don't swirl. Put it in the pressure pot. As it cures, the purple and blue fall through and spread out, which makes the nebula look.
Glow in the dark pen blanks
Glow powders are a lot denser and more granular than regular mica. Hold a jar of my glow powder next to a jar of Pinot Red mica and it's about three times heavier. A few things I've learned:
- Mix glow powders in very, very well.
- Wait until the resin is at the hot end of its working time, right before it has to go in the pressure pot, then do your mixing and pouring. Thicker resin and a shorter time before cure mean less time for heavy powder to sink.
- If you mix glow powders with light powders like macro color shift, interference or glitter, the glow powder wants to sink and the light ones want to stay on top. Keep it in mind, or accept some settling.
- For my red, blue and green glow swirl, the swirls were much clearer when glowing than in daylight. Next time I'd use a lot more glow powder so it looks good when it isn't glowing too.
Common problems and fixes
Colors bleed together and go muddy
Usually the resin was too cool and thin, or it was poured too hard. Wait until it's around 100 to 105°F, pour lightly so the color sits on top, and save the swirling for one pass at the end.
Bubbles in the finished blank
The resin got too hot before it went under pressure. Keep it under about 120°F before it goes in the pot. Have the pot ready before you start pouring, and don't start a multi-color pour past 100 to 105°F.
Light shows through the finished pen
Mica alone gets translucent when it's turned thin. Add more powder, or add the matching dye. Test it at final thickness in a cup before you pour.
Heavy powder settled to the bottom
Glow and dense pearl powders sink. Mix them in late, when the resin is hottest and thickest. Or use it on purpose, like the galaxy technique.
Resin didn't cure or stayed tacky
Don't use water-based dyes in polyurethane resin like Alumilite. Polyurethanes hate moisture and it can ruin the casting. Alcohol dyes work, but I don't think you can get an opaque color with them. Also don't dump in an absurd amount of dye with a little resin. There is an upper limit, though you'd have to work to hit it.
FAQ
How do you keep colors separated in color swirl pen blanks?
Temperature is the main thing. Let the resin heat up and thicken (I aim for 100 to 105°F), use opaque colors for contrast, pour lightly, and swirl once at the end with a skewer.
How much mica powder should I use in resin?
It depends on the look you want. A lot gives an opaque color. A little gives a transparent tint with sparkle. Start small, check it at your final thickness, and add more. You can't take it back out.
Why does glow in the dark powder sink in resin?
It's much denser than other powders. Mix it in very well and pour late, when the resin is close to curing, so it has less time to settle.
Does this work with epoxy?
I use Alumilite Clear, but the technique applies to other resins. The difference is how long the resin takes to heat up. Mica powder works in epoxy and other polyurethanes too.
Want to see how swirl and glow blanks turn out without casting your own? Take a look at my Green White Swirl or "Lava" pen blank, Glow In The Dark Alumilite pen blank and Black & White Swirl Grapevine & Alumilite pen blanks.



