Sale: 20% off everything through Dec 1
Wine Country Woodworks

Aluminum Honeycomb Pen Blanks: Casting and Turning "Alumicomb"

By Casey Martin · Updated

Video: Aluminum Honeycomb & Alumilite Pen Blanks - "Alumicomb"
Aluminum Honeycomb & Alumilite Pen Blanks - "Alumicomb"

I call my aluminum honeycomb pen blanks "Alumicomb": 1/8 inch cell aluminum honeycomb in blue and white Alumilite. Blue and white is my go-to color combination, and it's my favorite to test on a new material.

This guide covers how I make them: mixing the resin and colors, letting the honeycomb sink in, cutting the blanks and turning them. It also covers which colors to avoid and how to turn this stuff without a piece popping out of a cell.

Video: Aluminum Honeycomb & Alumilite Pen Blanks - "Alumicomb"
Aluminum Honeycomb & Alumilite Pen Blanks - "Alumicomb"

What you need

  • Aluminum honeycomb. I got mine from Zac Higgins at NV Wood Werks. He has 1/8 inch cell and 1/4 inch cell honeycomb, in different thicknesses (I've used a 2 inch thick piece for a display block and a thinner piece for pen blanks).
  • Alumilite resin, mixed by weight.
  • A mold sized for the block you want to cut blanks from.
  • A scale for weighing the resin.
  • Dyes and powders for color. For my blue I add interference blue pearl powder along with the dye.
  • Mixing cups and popsicle sticks: one clean cup for mixing the resin, plus one cup per color.
  • A barbecue skewer for swirling the colors.
  • A pressure pot.
  • A band saw for cutting the honeycomb to size and a table saw for cutting the cured block into blanks.
  • A lathe and a carbide tool with a sharp cutter for turning.
  • Sandpaper up to 2,000 grit and a buffing wheel for finishing.

Which honeycomb cell size to use

Both the 1/8 inch and 1/4 inch cell honeycomb can be used for pen blanks or really anything resin-casting related. That said, the smaller 1/8 inch cells are a little better for small turnings like pens and bottle openers, and the larger 1/4 inch cells suit bigger things like handles. My Alumicomb pen blanks use the 1/8 inch cell.

Step by step

  1. Cut the honeycomb to fit your mold.
    • I cut my honeycomb on the band saw.
    • Test-fit it before you mix anything. Honeycomb can be squished or bent a bit, so make sure it sits in the mold the way you want.
  2. Set up your color cups before you mix the resin.
    • Get one cup for each color and put the dye and powder for that color in the bottom of it. Have your popsicle sticks ready.
    • Add a little more dye than you think you need. You won't get every bit of it scraped out of the cup, and even a small amount of resin in each cup takes the color fine in my experience.
    • This setup means you aren't frantic and running around once the resin is mixed.
  3. Weigh and mix the resin in its own clean cup.
    • Mix the Alumilite by weight in a separate cup that gets no dye at all. It stays perfectly clear.
    • Mix the full amount you'd need to fill the mold as if there were no honeycomb in it. The honeycomb takes up almost no volume, so it won't raise the resin level. In my first honeycomb video I was half hoping pushing the honeycomb in would raise the resin enough. It didn't.
    • Once it's mixed, eyeball the clear resin into your color cups. You can give one color more than the others if you want more of it. For a two-color blank like Alumicomb I just split it between a blue cup and a white cup.
  4. Pour the resin into the mold first.
    • For pen blanks I pour all of the resin in before adding the honeycomb. I try to get about 50/50 blue and white everywhere I can.
    • It's hard to get both colors coming out at exactly the same speed, so move the colors around and add a little more in spots where you need it.
  5. Lay the honeycomb on the resin and let it sink.
    • Set the honeycomb on top and leave it alone. It sinks on its own. You'll see a shimmer go across it as it goes down, and it leaves little round swirls in the resin, which look really neat in the finished blanks.
    • I don't push it down. In the video it looks like I'm about to touch it, but I don't.
  6. Pressure the block.
    • My multi-color honeycomb block went in the pressure pot for about four hours.
  7. Cut the block into blanks on the table saw.
    • Cutting is pretty self-explanatory. I kept this block long rather than cutting it thinner. I do that more often than not now, especially with material I really like, because the person who buys it may want to make something other than a pen. My Alumicomb blanks are 5.5 inches long by 0.75 by 0.75 inches.
  8. Turn it slowly with a sharp cutter.
    • This is an advanced material to turn. It's not easy.
    • Make sure the cutter on your carbide tool is sharp, and take it slow. When I turned a bottle opener from one of these blanks, a little piece of resin popped out of one of the cells. My cutter was dull and I was going a little too fast because I wanted to get it finished.
    • It's 100% worth the time and effort if you take it slow.
  9. Sand and buff.
    • On my honeycomb display block I sanded up to 2,000 grit with my palm sander, then took it to the buffing wheel.
    • Buffing is the best finish I think there is on these hybrid materials. I do it on all of my pens and turnings now, and I highly recommend it.

Bigger pours: the older method

In my first honeycomb video I made a 2 inch thick block of 1/4 inch cell honeycomb and maple burl with seven colors (red, blue, green, yellow, orange, purple and white), and I did it differently. I put most of the honeycomb in the mold first, took the middle piece out, poured, and then pushed the middle piece in at the end. I was nervous that if all the honeycomb was in place and I didn't pour perfectly from the top, some cells wouldn't fill.

For pen blanks I now pour first and let the honeycomb sink, which is fun to watch and gives you those round swirls. You can do it the other way, but it's not usually the wise choice. A big multi-color pour is the exception: there I was worried about time, so I went with the older method.

Video: How To Resin Cast Aluminum Honeycomb
How To Resin Cast Aluminum Honeycomb

Common problems and fixes

A piece of resin pops out of a cell while turning

This happened to me on the bottle opener. The cause was a dull carbide cutter and going too fast. Change or sharpen the cutter and slow down.

Not enough resin to fill the mold

The honeycomb doesn't displace much, so mix as much as you would for the mold with nothing in it. If you do come up short, as I did on my seven-color block, you don't have to scramble to mix more. Let it cure and pour a second layer. With the honeycomb and wood in there, the next layer adheres really well. If you're stacking onto plain resin it can work fine, but rough the surface up with sandpaper first so it sticks. You will see a line where it was cast twice. With lots of colors and swirls it doesn't look that bad, but white makes it a little more obvious.

A color came out almost black

I used a violet dye with no powder in it, and it came out so dark it looked nearly black, even though it looked purple on the sides of the cup. If you're doing multiple colors, steer clear of the dark ones. When a dark color mixes with another one it just looks black instead of swirls. My blue was also pretty dark, but adding powder to it helped a lot.

Too much of one color in the cells

On my seven-color block I put a lot of white into the honeycomb cells, more came out than I meant, and it covered up the other colors. It still looked cool, but next time I'd use about half that much white and still use the rest of the colors in the cells.

Uneven color split

Getting exactly 50/50 is always a bit of a crapshoot. Move the colors around in the mold and add more in the thin spots as you pour.

FAQ

Does aluminum honeycomb take up space in the resin?

Almost none. Pour as much resin as you would if you weren't using honeycomb at all.

Should I put the honeycomb in the mold before or after the resin?

For pen blanks I pour the resin first and lay the honeycomb on top so it sinks on its own. I only put the honeycomb in first on a big multi-color pour where time was the worry.

What is the best honeycomb cell size for pen blanks?

Both work, but the 1/8 inch cell is a little better for pens, bottle openers and other small turnings. The 1/4 inch cell suits larger pieces like handles.

Are aluminum honeycomb pen blanks hard to turn?

Yes, they're an advanced material. Use a sharp carbide cutter and go slow, or you risk resin popping out of a cell.

What colors look best with aluminum honeycomb resin?

Blue and white is my go-to combination and my favorite for testing new materials. White is the best color in a multi-color pour because when it blends with another color it just makes swirls. Avoid dark colors like violet without powder; they turn almost black.

How do you finish honeycomb blanks?

I sand up to 2,000 grit and then buff. Buffing is the best finish I've found for these hybrid materials.

If you want to skip the casting and go straight to turning, my Alumicomb honeycomb pen blanks are 1/8 inch cell aluminum honeycomb in blue and white swirl Alumilite. For more on working with this resin, see my Alumilite resin casting tips.

Products in this guide

← All guides